Razvoj postupaka sinteze polimernih mreža i hibridnih materijala

Abstract

U ovom radu vršena su istraživanja u cilju razvoja novih postupaka sinteze za nekoliko vrsta polimernih mreža i hibridnih biopolimernih materijala za specijalne primene. Cilj je bio da se razvije novi postupak sinteze rotaksana na bazi poli(etilen glikola) i β-ciklodekstrina kaoprekursora mreža. Dobijeni prekursori mreža iskorišćeni su za sintezu topoloških gelova koji su umreženi preko hidroksilnih grupa ciklodekstrinskih prstena. Analiziran je i uticaj količine umreživača, odnosno gustine umreženja, na svojstva bubrenja. Proučavan je i uticaj nanopunila na svojstva modelnih epoksi mreža na bazi bisfenola A i poli(oksi propilen) diamina. Kao punila korišćene su nanočestice nemodifikovanog i površinski modifikovanog titanijum(IV)oksida (TiO2). Dinamičko-mehaničkom analizom potvrđen je ojačavajući efekat punila. Razvijen je postupak sinteze poli(D,L-laktida) u mikrotalasnom polju, čime je drastično smanjeno vreme polimerizacije (sa 150 sati na 15 minuta) u odnosu na klasičnu termosintezu. Sintezom poli(laktida) kao i kopolimera poli(laktida) sa biorazgradivim monomerima (na osnovu obnovljivih sirovina) dobijeni su materijali izuzetnih ekoloških svojstava. Poli(laktid) se odlikuje veoma dobrim mehaničkim svojstvima i biorazgradivošću, dok je blok-kopolimerizacijom sa drugim biorazgradivim monomerima vršena sinteza termoplastičnih poliestara. Variranje dužine segmenata je ostvareno sintezom adekvatnih oligomera kao prekursora za kopolimerizaciju. Vršeno je projektovanje sirovinskog sastava segmentiranih elastomera kod kojih postojanje mekih i tvrdih segmenata ima za posledicu mikrofaznu separaciju faza što u toku eksploatacije utiče na mehanička svojstva i mogućnost III razgradnje. Na taj način dobijeni su elastomerni materijali željenih svojstava. Metodama FTIC i 1H NMR spektroskopijom potvrđena je pretpostavljena struktura segmenata i finalnih termoplastičnih poliestara. Analizom molskih masa poliestara metodama gel propusne hromatografije, viskozimetrije i osmometrije napona pare, potvrđena je izuzetna kontrola reakcija polimerizacije i uspešnost primenjenih metoda sinteze. Analiza toplotnih svojstava blok poliestara diferencijalno skenirajućom kalorimetrijom je pokazala da zbog nemešljivosti faza, tvrdih i mekih segmenata, finalni blok poliestri mogu da pokažu razlike u temperaturama faznih transformacija u zavisnosti od dužine i udela segmenata. Termogravimetrijskom analizom je potvrđen uticaj dužine segmenata i faznog razdvajanja na toplotna svojstva termoplastičnih poliestara. Očekuje se da će sintetisani materijali biti podesni za primene u inženjerstvu tkiva, a posebno kao materijali za kontrolisano otpuštanje lekova.

The primary goal of the work described in this thesis was to develop new methods for the synthesis of polymer networks and hybrid biopolymers for special applications. The purpose was a development of synthesis procedure for the preparation of rotaxane based on poly(ethylene glycol) and β-cyclodextrin, as network precursors. These network precursors were then cross-linked through hydroxy groups on cyclodextrine rings. Polyrotaxanes are intermediary products in the synthesis of topological gels and they are formed by the insertion of the linear polymer chains of poly(ethylene oxide) into the β-CD cavities. In this work polyrotaxanes from acetylated-β-CD and poly(ethylene oxide) were synthesized. The influence of crosslinker contents, and crosslink density on swelling properties was investigated. The influence of synthesis parameters and filler modification on reactions and final properties of organic-inorganic hybrid materials based on epoxy resin and an organically modified titanium(IV)oxide (TiO2) was investigated. Dynamic-mechanical analysis was used to determine reinforcement effect of nanofiller on the epoxy resin properties. The aim of this work was the investigation of microwave irradiation on the polymerization of D,L-lactide. It was found that if heating is carried out in the microwave field polymerization time of D,Llactide rapidly decreases from 150 hours to 15 minutes. Environmentally friendly materials were obtained from poly(lactide) and copolymers of poly(lactide) and monomers based on renewable resources. Poly(lactide) is biocompatible and biodegradable polymer with high stretching and low extension capacities. It has been used for the production of orthopedic fraction fixators and sutures surgery. Poly(lactide) was used for thermoplastic polyester (TPE) synthesis. Most thermoplastic polyesters derive their properties from segmented or block structures which are achieved by alternating hard and soft segments. FT-IR and 1H NMR spectroscopy were confirmed the assumed structure of segments and final thermoplastic polyesters. Since the properties of these materials strongly depend on the degree of phase separation, the influence of the lenghts of soft and hard segment on final properties of obtained TPEs was studied. Analysis of molecular mass of these polyesters by gel permeation chromatography, vapor pressure osmometry and viscozimetric analysis confirmed that good control of polymerization was achieved and that synthesis methods were successful. Thermal properties were characterized by means of differential scanning calorimetry (DSC) and thermo-gravimetric analysis (TGA). Phase separation had strong influences on thermal properties of obtained TPEs. DCS measurements showed that due to poor mixability of hard and soft segments, final block polyesters could have different temperatures of phase transitions depending on the length of the segments. Thermal degradation and the influence of phase separation on thermal stability of segmented thermoplastic polyesters were confirmed by nonisothermal analysis, using thermogravimetric analysis. It is expected that synthesized materials will be suitable for tissue engineering and as drug carriers.